| Ratings |
| Rated Voltage (MAX) | 50V | |
| Rated Current (MAX) | 1.0A [AC (virtual value) / DC] | |
| Ambient temperature Range | -25 +85 | |
| Electrical Performance |
| Contact Resistance | 20 m MAX | Mate applicable and measure by dry circuit, 20mV MAX, 10mA. |
| Insulation Resistance | 500M MIN | Mate applicable and apply 500V DC between adjacent terminal or ground. |
| Dielectric Strength | No Breakdown | Mate applicable and apply 500V AC (virtual value) for 1 minute between adjacent terminal or ground. |
| Mechanical Performance |
| Insertion Force | 5 * n (N) MAX | Insert and extract applicable at the speed rate of 253mm/minute. |
| Withdrawal Force | 0.3 * n (N) MIN | Insert and extract applicable at the speed rate of 253mm/minute. |
| Terminal Retention Force | 10 N MIN | Pull the terminal at the speed rate of 253mm per minute. |
| Environmental Performance and Others |
| Repeated Insertion and Withdrawal (Contact Resistance) | 60 m MAX | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute. |
| Temperature Rise (under rated current) | 30 MAX | Carrying rated current load. (UL 498) |
| Vibration (Discontinuity) | 1 ms MAX. | Amplitude: 1.5mm P-P; Sweep time: 10-55-10Hz in 1 minute; Duration: 2 hours in each X.Y.Z. axes; DC 1mA energized. |
| Shock (Discontinuity) | 1 ms MAX. | 490m/s {50G}, 3 strokes in each X.Y.Z. axes; DC 1mA energized. |
| Heat Resistance (Contact Resistance) | 60 m MAX | 852, 96 hours; then return to room temperature for 1-2 hours. |
| Heat Resistance (Appearance) | No Damage | 852, 96 hours; then return to room temperature for 1-2 hours. |
| Cold Resistance (Contact Resistance) | 60 m MAX | -402, 96 hours; then return to room temperature for 1-2 hours. |
| Cold Resistance (Appearance) | No Damage | -402, 96 hours; then return to room temperature for 1-2 hours. |
| Cold Resistance (Dielectric Strength) | Must meet 4.1.3 | -402, 96 hours; then return to room temperature for 1-2 hours. |
| Humidity (Insulation Resistance) | 100 M MIN | Temperature: 402; Relative Humidity: 90-95%; Duration: 96 Hours; then measure within 0.5 hours at room temperature. |
| Humidity (Appearance) | No Damage | Temperature: 402; Relative Humidity: 90-95%; Duration: 96 Hours; then measure within 0.5 hours at room temperature. |
| Temperature Cycling (Contact Resistance) | 60 m MAX | 5 cycles of: a) -553 30 minutes; b) 852 30 minutes; with 10-15 minutes of room temperature/humidity between cycles. |
| Temperature Cycling (Appearance) | No Damage, Corrosion | 5 cycles of: a) -553 30 minutes; b) 852 30 minutes; with 10-15 minutes of room temperature/humidity between cycles. |
| Salt Spray (Contact Resistance) | 60 m MAX | 484 hours exposure to a salt spray from the 51% solution at 352. After test, wash with room temperature water and dry at room temperature. |
| SO2 Gas (Contact Resistance) | 60 m MAX | 24 hours exposure to 505ppm SO2 gas at 402. |
| SO2 Gas (Appearance) | No Damage | 24 hours exposure to 505ppm SO2 gas at 402. |
| NH3 Gas (Contact Resistance) | 60 m MAX | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. |
| Solder ability (Solder Wetting) | 95% or more wetting area | Terminal tip immersed in a 2355 tin bath for 20.5 sec. |
| Resistance to Soldering Heat (Appearance) | No Damage, Deformation | At least 5 times under conditions of 305 sec. in a 2605 hot air oven. |
